How Do I Set Up My NETGEAR EAX15 Extender?

The NETGEAR EAX15 setup is simple, and it can significantly improve the reach of your wireless network. Start by putting the NETGEAR EAX15 Extender in the middle of the area that is covered by your current WiFi router. Turn on the extension and watch for a stabilization of the LED lights. Link your PC or mobile device to the WiFi network of the extender, which is typically called “NETGEAR_EXT.” Once connected, type “” into the address bar of a web browser. To log in and adjust your extender settings, follow the on-screen directions. It might be necessary for you to select your current WiFi network and provide its password. After that, the extender will build a new extended network to strengthen your WiFi signal in places where it isn’t as strong. Following setup, establish a connection.

How do I setup my Netgear EAX15 extender manually?

  • For the first configuration, place the extender in the same room as your WiFi router.
  • After plugging the extender into a power source, watch for it to start up. A solid green power LED should be present.
  • Navigate to the WiFi settings on your computer or mobile device.
  • Link to the extender’s default WiFi network, which is typically called “NETGEAR_EXT.”
  • Open a web browser on your linked device (such as Chrome, Firefox, or Safari).
  • Enter “” or “,” which are common default IP addresses for NETGEAR extenders, in the address bar and hit Enter.
  • A username and password entry form will appear. Until you have modified them previously, use the default credentials, which are often “admin” for both the username and password.
  • You will be guided through the setup procedure using the web interface of the extender. The directions displayed on the screen should be followed.
  • You might have to choose your current WiFi network and provide the password.
  • In the configuration, choose the “Extender” mode or a comparable setting.
  • The password and name of the expanded network (SSID) may be modifiable. Adjust these parameters as necessary.
  • The extender will reboot after it has finished setting up. Reconnect your device to your primary WiFi network and detach it from the extender’s network once it has restarted.
  • For best coverage, move the extension to the desired spot. As long as it covers the targeted areas, make sure it’s inside your router’s WiFi range.
  • After making any changes to the SSID and password, reconnect your devices to the expanded network.

Note: If you need any assistance regarding your Netgear EAX15 wifi extender so contact our technician or visit the official website, which is mywifiext.

How do I connect my extender to WPS?

  • Place your extender such that it has a strong signal and is still inside the coverage area of your current WiFi network.
  • Turn on your extension by plugging it in. When the extender has finished booting up, confirm that the Power LED is solid green.
  • Locate the WPS button on the extension. Usually, it’s found on the device’s front or side.
  • For a few seconds, press and hold the WPS button on your extension until the WPS LED begins to blink. This means that you can attach the extender at this point.
  • Go to your WiFi router and look for the WPS button after two minutes of pushing the extender’s WPS button.
  • After two minutes, click the WPS button on the extension and then the WPS button on your WiFi router.
  • After a successful connection, the extender’s WPS LED will solidify and cease to flash. This could take a minute or two to complete.
  • You can move the extender inside your router’s WiFi range to the desired position once the connection has been established.
  • Verify that the enlarged network can now be accessed by the devices in the expanded area.

How do I log into my Netgear extender?

  • Connect a PC or mobile device to the WiFi network that your Netgear extender has broadcast. This network is frequently referred to as “NETGEAR_EXT” or a similar moniker.
  • On the linked device, open a web browser. Microsoft Edge, Chrome, Firefox, and Safari are a few examples.
  • Enter the Netgear extenders’ default IP address in the browser’s address bar. Examples of common default addresses are “” and “” Hit the Enter key.
  • You ought to be sent to the login page. You have to enter your username and password here.
  • For your Netgear extender, enter the default login and password. The default credentials are frequently:
  • Login as admin.
  • Password: this one
  • Use the revised details if you have previously changed your login credentials.
  • You should be able to access the dashboard or settings of the extension after providing the right login and password.
  • You can adjust your Netgear extender’s WiFi settings, security settings, and other settings after logging in.
  • It’s best practice to log out of the extender’s interface after making adjustments or verifying settings, particularly if you’re using a shared computer or gadget.

By hand, how can I upgrade the firmware on my Netgear device?

  • Enter the web interface of your Netgear router or extender and log in with a web browser. In the address bar, type the router’s IP address (usually “” or “”) and log in using your admin credentials. Verify the router’s or extender’s firmware version by checking its status.
  • Please visit the Netgear support website and select the “Download Center.” To locate the most recent firmware version for your equipment, enter the model number of your router or extension.
  • Save the most recent firmware file to your computer. To prevent incompatibilities, make sure the firmware you download is appropriate for the model of router or extension you own.
  • Navigate back to the web interface of the extender or router. Check the settings menu for an option like “Firmware Update” or something similar. Select the firmware file you downloaded and either upload or install it. To start the update procedure, adhere to the on-screen directions.
  • Give the firmware upgrade procedure time to finish. Your router or extender might reboot throughout this few-minute process. The process should not be interrupted as this could cause device issues.

In what way can I reboot the Netgear EAX15 extender?

  • Regarding your NETGEAR EAX15 Extender, search for the reset button. Model-specific variations exist in the reset button’s location. In order to avoid inadvertent pressing, the button is typically small and may be sunken.
  • Towels that fit inside the reset button hole, such as paperclips, should be obtained. For a certain amount of time, usually five to ten seconds, you might need to push and hold the reset button.
  • To reset the button, press and hold it.
  • Holding the paperclip in place, press the reset button. Holding it down will cause the extender’s LED lights to blink, signaling the start of the reset procedure.
  • Release the reset button after the LED lights have begun to blink. Following a reboot, the extender will return to its factory default configuration.


As a DIGITALTECHSIDE author, the majority of our articles have been focused on technology, blogging, business, lifestyle, social media, web design and development, e-commerce, money, health, education, entertainment, SEO, travel, and sports. Contact us at if you have questions of anything.